OMTech 60W 20x28in Workbed CO2 Laser Engraver Cutter with CW3000 Water Chiller

  

OMTech 60W CO2 Laser Engraver. Combining ease of use with advanced capability, this intuitive 60W CO2 laser engraver delivers professional results at a fraction of the cost.

Equipped with a powerful 60-watt water-cooled laser tube, high-precision stepper motor, and a top-quality LCD control board, it features our largest engraving surface (28" x 20") with a height-adjusting lift table and four-way pass-through doors to accommodate oversized and irregular-shaped objects, making it one of our most highly capable engraving machines. Simply plug in the USB connector to your computer system and you're ready to start your laser engraving story! Check out our many Accessories and Parts to go along with your laser machine!

60W CO2 laser tube with an estimated lifetime of up to 2,000 operation hours depending on power setting usage and water cooling performance. PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows. Low Power 10-40% = 1,700-2,000 Hours.

Moderate Power 40-70% = 1,300-1,500 Hours. High Power 70-100% = 800-1,000 Hours. Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber.

Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany. CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered. The intuitive control panel with a digital display allows complete control of the laser head, pausing and stopping projects, adjusting laser power and speed settings, file viewing, and project framing via Windows-compatible RDWorks v8.

Front & back and 19?? On either side-allows you to feed material into the workbed from any direction, letting you cut materials larger than the bed size by sliding them across the engraving table.

This spacious 2.4-gallon (9L) water tank runs at 2.6 gpm to remove heat for every 1°C rise in water temperature from your 60W below CO2 laser tube as it works. (500×700 mm) workbed gives you plenty of space to work on wood, rubber, plastic, paper, fabric, leather, ceramics, tile, fiberglass, marble, stone, and more-even before you open the integrated pass-through doors that permit you to work on even larger pieces! Either workbed can be automatically raised and lowered at the push of a button for more efficient processing.

The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work. The E-Stop safety button immediately stops the machine in case of emergency. Engraving Depth: 0.25 in. Engraving Speed: 23.6 ips (600 mm/s).

Cutting Speed: 15.7 ips (400 mm/s). Workbed Height Range: 9 in. Front/Back Pass Size: 32.87×3.94 in. Side Pass Size: 19.69×0.71 in.

Included Software: RDWorks 8, CorelLaser. Graphic Operating Modes: Optimized Raster, Vector, and Combined. Transfer Interface: Flash Drive, USB Cord, Ethernet Cord.

Net Weight: 229.3 lb. Machine Dimensions: 48.8 x 34.3 x 26.4 in. Laser Wavelength: 10.6 µm. 1 × CO2 Laser Engraver. 1 × Maintenance Tool Kit.

1 × USB Flash Drive (with Software). 1 × Pack of Laser Test Paper. 1 × Tube of Silicone Insulation. Flow: 2.6 gpm (10L/min).

Inlet/Outlet Port Diameter: 2/5 in. 1 x Alarm Signal Output Plug. 1 x Spare Fuse (held near the rear power socket). If the weight of your order exceeds 150 lbs.

Special circumstances will be stated clearly in the listing. Please check everything carefully after you receive the parcel, as any damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer.

Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Parts must be resaleable and in the original packaging.

We cannot take back used products. We cannot take back installed or tired products. We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria. Return request need to be within 30 days of receipt. OMTech is a collaboration of 30-yr industry vets and promising new techs in Anaheim, California.

Our affordable but quality lasers and US-based support quickly grew us into the largest online brand for precision engraving. Alongside our skilled & helpful staff, OMTech users have built up a supportive online family in our forums and social media, sharing inspiration and sharpening their DIY skills together.

We love keeping the OMTech family on the cutting edge of laser crafting because we know our growth is inseparable from your success. All emails will be responded to within 12-24 hours. One 45-minute Virtual Tech Support appointment with OMTech Specialists in Anaheim, California.