1 x Laser Engraver Machine. 1 x USB Type-A to Type-A Cable.
1 x Ethernet to Ethernet Cable. 1 x Stainless Steel Clamp.
Engraving Depth: 0.25 in. Workbed Height Range: 9 in.Front/Back Pass Size: 25×1.46 in. Engraving Speed: 23.6 ips (600 mm/s). Cutting Speed: 15.7 ips (400 mm/s). Included Software: RDWorks 8, CorelLaser. Graphic Operating Modes: Optimized Raster, Vector, and Combined. Transfer Interface: Flash Drive, USB Cord, Ethernet Cord. Machine Dimensions: 40.2×25.6×24.8 in.
Laser Wavelength: 10.6 µm. Laser Tube Diameter: 2 in.
Laser Tube Length: 34.6 in. If you must modify your. Special circumstances will be stated clearly in the listing.
Please check everything carefully after you receive the parcel, as any damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described.Parts must be resaleable and in the original packaging. We cannot take back used products.
We cannot take back installed or tired products. We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria.
Return request need to be within 30 days of receipt. The device may have some signs of cosmetic wear and/or structural damage, but is fully operational and functions 100% as intended. The device may have some cosmetic wear and/or signs of use but is fully operational and functions 100% as intended. The device has minimal signs of use but is fully operational and functions 100% as intended. PLEASE NOTE: The images shown in this listing do not fully represent the cosmetic condition of the machine.
This machine has undergone a thorough QA inspection by an OMTech Specialist, and each component has been repaired and tested for full operational performance. View condition examples of previous Pre-Owned models please see picture above. 70W CO2 laser tube with an estimated lifetime of up to 2,000 operation hours depending on power setting usage and water cooling performance. PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows.Low Power 10-40% = 1,700-2,000 Hours. Moderate Power 40-70% = 1,300-1,500 Hours. High Power 70-100% = 800-1,000 Hours. Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber. Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany. CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered. The intuitive control panel with a digital display allows complete control of the laser head, pausing and stopping projects, adjusting laser power and speed settings, file viewing, and project framing via Windows-compatible RDWorks v8.
Front & back and 17?? On either side-allows you to feed material into the workbed from any direction, letting you cut materials larger than the bed size by sliding them across the engraving table. The laser head is equipped with an automatic focus adjustment that you can use directly from the control panel, eliminating tedious manual adjustment.Our 1000 mm CO2 laser tube provides 70W of power for up to 2000 hours or lasts twice as long when consistently used at lower settings. A crystal-clear LCD display provides real-time information about the device's electric current and autocorrects faults, reducing damage to your laser tube and power supply in the rare case of improper ammeter connections. The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes.
The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work. The E-Stop safety button immediately stops the machine in case of emergency.1 x Venting Exhaust Duct 4 ft. 1 x USB Drive with Software.
Engraving Depth: 0.35 in. Workbed Height Range: 5.9 in. Front/Back Pass Size: 40.75×1.97 in.
Side/Side Pass Size: 28.66×0.79 in. Machine Dimensions: 56.7×42×37.8 in. Laser Tube Model: EFR F2. Laser Tube Diameter: 3.2 in.Laser Tube Length: 49.2 in. Focal Lens Diameter: 18 mm. If the weight of your order exceeds 150 lbs. OMTech is a collaboration of 30-yr industry vets and promising new techs in Anaheim, California.
Our affordable but quality lasers and US-based support quickly grew us into the largest online brand for precision engraving. Alongside our skilled & helpful staff, OMTech users have built up a supportive online family in our forums and social media, sharing inspiration and sharpening their DIY skills together. We love keeping the OMTech family on the cutting edge of laser crafting because we know our growth is inseparable from your success.All emails will be responded to within 12-24 hours. One 45-minute Virtual Tech Support appointment with OMTech Specialists in Anaheim, California.
This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving". The seller is "omtechlaser" and is located in this country: US. This item can be shipped to United States.