OMTech 80W 35x24 CO2 Laser Engraver Cutter Ruida Autofocus Upgraded Model

OMTech 80W 35"x24" CO2 Laser Engraver Cutter Ruida Autofocus Upgraded Model. Bring your ideas to life with OMTech's laser engraver AF series! This powerful 80W CO2 laser engraver continues to uphold our high standards with its Ruida control panel, bundled RDWorks 8 software, long-lasting laser tube, wide 24x35 inch working area, and 4 pass-through doors that allow even larger pieces to be worked on. This laser cutting and engraving machine provides dual work platforms: a honeycomb bed for smaller objects and a firmer aluminum knife blade bed for larger, harder substrates like acrylic blocks. This engraver is able to automatically focus the laser at the push of a button and its 86-stepper motor raiser and lowers either workbed at the push of a button, making your work even more convenient and efficient.

In addition to high quality, durability, and the usual long service life, this laser cutter is also very practical, with a built-in air assist blowing dust and debris away from the laser head and into the large-capacity hopper below for easy cleanup at the end of the day. Compatible with most third-party graphic software, this laser cutter allows you to turn your fresh ideas into reality on a large scale.

Simply upload your designs using the included software or via the Ethernet or USB ports, choose your substrate, and the laser will engrave and cut your design into wood, paper and cardboard, plastics and acrylic, leather, fabric, and other nonmetallic materials with pinpoint precision. With OMTech's careful engineering, quality materials & assembly, and good name, you can do no better for all your marking, engraving, and cutting projects at home or in your workshop. To go along with your laser machine! The RUIDA Motherboard and intuitive RD Control System is easy to use and offers advanced capabilities. Compatible with third party software like LightBurn and AutoCAD. (1497×48 mm) front & back and 38?? (970×20 mm) on either side-allows you to work pieces much larger than the bed size by sliding them through as you go. The laser head is equipped with an automatic focus adjustment that you can use directly from the control panel, eliminating tedious manual adjustment. Powerful EFR F2 Laser Tube. The 80W laser tube can reach a peak power wattage up to 100W, allowing you to cut deeper and engrave thicker materials. The Air Assist ventilation function directs hazardous debris away from the engraving surface and into the waste collection bin, which takes only seconds to empty manually. (600×900 mm) engraving table includes both honeycomb and aluminum knife beds to handle a wide variety of nonmetallic substrates, including wood, leather, fabric, stone, paper, and much more! One USB port reads flash drives while the other connects directly to your PC via dedicated cable. The Ethernet port allows you to work remotely online. Equipped with X and Y stepper motors for efficient power transmission between the guide rails with high precision and long service life. A red dot pointer mounted on the laser head quickly indicates engraving points, marks the machine's path, and identifies positioning sizes, allowing an effortless project setup process.

The laser nozzle can extend downwards up to 1.75 or be fully retracted, allowing more control over different focal distance setups. A pre-installed air compressor guides a pressurized air stream through the laser head nozzle to displace debris, heat, and combustible gases from the engraving surface and laser beam path, keeping your workbed cleaner and engravings more precise. Pre-installed hoses along with the included water pump allow for a fast and easy setup. Only use with distilled water, ensuring it stays between 60-70°F (16-21°C). A pressure flow sensor monitors water flow throughout the laser engraving process and prevents the laser from firing if water stops circulating through the laser tube.

The crystal-clear LCD displays on the surface of the machine monitor the electric current, easily adjusted by nearby knobs, visualizing the working current and power. The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work. Indicator Lights & Emergency Stop.

Three indicator lights keep you easily aware of your machine's operation while the emergency stop immediately cuts the laser and stops all moving parts in the event of accident. Engraving Depth: 0.35 in.

Workbed Height Range: 5.9 in. Front/Back Pass Size: 40.75×1.97 in. Side/Side Pass Size: 28.66×0.79 in. Engraving Speed: 23.6 ips (600 mm/s). Cutting Speed: 15.7 ips (400 mm/s). Included Software: RDWorks 8, CorelLaser. Graphic Operating Modes: Optimized Raster, Vector, and Combined. Transfer Interface: Flash Drive, USB Cord, Ethernet Cord. Machine Dimensions: 56.7×42×37.8 in.

Laser Tube Model: EFR F2. Laser Wavelength: 10.6 µm. Laser Tube Diameter: 3.2 in. Laser Tube Length: 49.2 in. Focal Lens Diameter: 18 mm.

1 x Laser Engraver Machine. 1 x Ethernet to Ethernet Cable. 1 x Venting Exhaust Duct 4 ft. 1 x USB Type-A to Type-A Cable.

1 x USB Drive with Software. 1 x Stainless Steel Clamp.

80W CO2 laser tube with an estimated lifetime of up to 8,000 operation hours depending on power setting usage and water cooling performance. PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows. Low Power 10-40% = 7,000-8,000 Hours.

Moderate Power 40-70% = 5,000-6,500 Hours. High Power 70-100% = 3,000-4,000 Hours.

Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber. Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany. CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered. Master, AmericanExpress, Discover, Google Pay. If you must modify your. Laser tube and power supply.

Special circumstances will be stated clearly in the listing. If your item has been damaged in transit or.

Please check everything carefully after you receive the parcel, as any. Damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Parts must be resaleable and in the original packaging. We cannot take back used products. We cannot take back installed or tired products. We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria. Return request need to be within 30 days of receipt. Feedback as much as you do.

If for some reason there is. As an emerging leader in manufacturing and exporting, we specialize in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for over 10 years.

It is our mission to provide innovative products and competitive prices to satisfy you. Please submit all enquires via the "Ask a Question" tab, located at the bottom of this page.

This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving". The seller is "premiumautopart" and is located in this country: US. This item can be shipped to United States.

Brand: OMTech
MPN: AF2435-80
Engraving Method: Laser
Type: Engraving Machine
Material: Acrylic, Felt, Foam, Glass,Neoprene, Paper, Plastic, Rubber,Wood
Engraving Application: Gift Personalization, Housegoods, Office Signage, Plaque, Signs
Power: 80 W
Machine Operation: Computerized
Name Tag Style: Badge
Model: SH-G690
Input Power: 110V/60Hz AC
Processing Area: 24×36 in. Engraving Depth: 0.35 in.

(9 mm)
Workbed Adjustment: Electric
Workbed Height Range: 5.9 in. (150 mm)
Front/Back Pass Size: 40.75×1.97 in. (1035×50 mm)
Side/Side Pass Size: 28.66×0.79 in. Engraving Speed: 23.6 ips (600 mm/s)
Max. Cutting Speed: 15.7 ips (400 mm/s)
Included Software: RDWorks 8, CorelLaser
Graphic Operating Modes: Optimized Raster, Vector, and Combined
Transfer Interface: Flash Drive, USB Cord, Ethernet Cord
Net Weight: 441 lb.
(200 kg)
Machine Dimensions: 56.7×42×37.8 in. (144×107×96 cm)
Rated Power: 80W
Laser Tube Model: EFR F2
Laser Wavelength: 10.6 μm
Laser Tube Diameter: 3.2 in. (80 mm)
Laser Tube Length: 49.2 in. (1250 mm)
Laser Tube Warranty: 1 Year
Focal Lens Diameter: 18 mm
Focal Length: 2½ in.
(63.5 mm)
Mirror Diameters: 25 mm
UPC: 758232252475