OMTech 70W 16x30in Autofocus CO2 Laser Engraver w. Best Choice Accessories Pack

  

OMTech 70W 16x30in Autofocus CO2 Laser Engraver w. Bring your ideas to life with OMTech's laser engraver AF series! This powerful 70W CO2 laser engraver continues to uphold our previous high standards with its Ruida control panel, included RDWorks 8 and CorelLaser software suite, 1100 mm laser tube, wide 16x30 inch working area, and 4 pass-through doors that allow even larger pieces to be worked on. This laser cutting and engraving machine provides dual work platforms: a honeycomb bed for smaller objects and a firmer aluminum knife blade bed for larger harder substrates like acrylic blocks.

The engraver's 86 stepper motor raises and lowers either workbed at the push of a button to make your work even more convenient and efficient. In addition to high quality, durability, and the usual long service life, this laser cutter is also very practical, with a built-in air assist blowing dust and debris away from the laser head and into the large-capacity hopper below for easy cleanup at end of the day. Compatible with most third-party graphic software, this laser cutter allows you to turn your fresh ideas into reality on a large scale. Simply upload your designs using the included software or via the Ethernet or USB ports, choose your substrate, and the laser will engrave and cut your design into wood, paper and cardboard, plastics and acrylic, leather, fabric, and other nonmetallic materials with pinpoint precision.

With OMTech's careful engineering, quality materials & assembly, and good name, you can do no better for all your marking, engraving, and cutting projects at home or in your workshop. To go along with your laser machine! The intuitive control panel with a digital display allows complete control of the laser head, pausing and stopping projects, adjusting laser power and speed settings, file viewing, and project framing via Windows-compatible RDWorks v8.

Front & back and 20¾? On either side-allows you to feed material into the workbed from any direction, letting you cut materials larger than the bed size by sliding them across the engraving table. The laser head is equipped with an automatic focus adjustment that you can use directly from the control panel, eliminating tedious manual adjustment. 70W YL H1 Laser Tube. Filled laser tube is both stable and long-lasting, with a MTTF of over 8000 hours. The Air Assist ventilation function directs hazardous debris away from the engraving surface and into the waste collection bin, which takes only seconds to empty manually. One USB port reads flash drives while the other connects directly to your PC via dedicated cable. The Ethernet port allows you to work remotely online. Equipped with X and Y stepper motors for efficient power transmission between the guide rails with high precision and long service life. A red dot pointer mounted on the laser head quickly indicates engraving points, marks the machine's path, and identifies positioning sizes, allowing an effortless project setup process. The laser nozzle can extend downwards up to 1.75 or be fully retracted, allowing more control over different focal distance setups. A pre-installed air compressor guides a pressurized air stream through the laser head nozzle to displace debris, heat, and combustible gases from the engraving surface and laser beam path, keeping your workbed cleaner and engravings more precise.

(400×750 mm) workbed gives you plenty of space to work on wood, rubber, plastic, paper, fabric, leather, ceramics, tile, fiberglass, marble, stone, and more-even before you open the integrated pass-through doors that permit you to work on even larger pieces! Pre-installed hoses along with the included water pump allow for a fast and easy setup.

Only use with distilled water, ensuring it stays between 60-70°F (16-21°C). A pressure flow sensor monitors water flow throughout the laser engraving process and prevents the laser from firing if water stops circulating through the laser tube. A crystal-clear LCD display provides real-time information about the device's electric current and autocorrects faults, reducing damage to your laser tube and power supply in the rare case of improper ammeter connections. The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work.

The E-Stop safety button immediately stops the machine in case of emergency. Engraving Depth: 0.28 in.

Workbed Height Range: 5.9 in. Front/Back Pass Size: 34.84×1.97 in. Side/Side Pass Size: 20.87×0.75 in. Engraving Speed: 23.6 ips (600 mm/s). Cutting Speed: 15.7 ips (400 mm/s).

Included Software: RDWorks 8, CorelLaser. Graphic Operating Modes: Optimized Raster, Vector, and Combined.

Transfer Interface: Flash Drive, USB Cord, Ethernet Cord. Net Weight: 165.3 lb. Machine Dimensions: 49.6×34.3×36.2 in. Laser Tube Model: Yongli H1. Laser Wavelength: 10.6 µm. Laser Tube Diameter: 2.4 in.

Laser Tube Length: 43.3 in. Focal Lens Diameter: 18 mm. 1 x Laser Engraver Machine.

1 x CW-3000 Water Chiller. 1 x Ethernet to Ethernet Cable. 1 x Venting Exhaust Duct 4 ft.

1 x USB Type-A to Type-A Cable. 1 x USB Drive with Software.

1 x Stainless Steel Clamp. 70W CO2 laser tube with an estimated lifetime of up to 8,000 operation hours depending on power setting usage and water cooling performance.

PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows. Low Power 10-40% = 7,000-8,000 Hours. Moderate Power 40-70% = 5,000-6,500 Hours. High Power 70-100% = 3,000-4,000 Hours. Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber.

Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany.

CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered.

Master, AmericanExpress, Discover, Google Pay. If you must modify your. Laser tube and power supply. Special circumstances will be stated clearly in the listing. If your item has been damaged in transit or. Please check everything carefully after you receive the parcel, as any. Damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Parts must be resaleable and in the original packaging. We cannot take back used products.

We cannot take back installed or tired products. We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria.

Return request need to be within 30 days of receipt. Feedback as much as you do. If for some reason there is. As an emerging leader in manufacturing and exporting, we specialize in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for over 10 years. It is our mission to provide innovative products and competitive prices to satisfy you.

Please submit all enquires via the "Ask a Question" tab, located at the bottom of this page. This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving". The seller is "acautoparts04" and is located in this country: US. This item can be shipped to United States.

1. Brand: OMTech
2. MPN: AF1630-70
3. Engraving Method: Flat Engraver
4. Type: Engraving Machine
5. Engraving Application: Office Signage
6. Machine Operation: Computerized
7. Name Tag Style: Pin
8. Tool Type: Flexible Shaft Machine/Rheostat
9. Application Shape: Square
10. Model: SH-G470
11. Bundle Description: laser engraver with rotary axis water chiller lightburn
12. Laser Power Supply: 110V/60Hz AC
13. Engraving/Cutting Area: 16″ × 30″ (40×75 cm)
14. Engraving/Cutting Thickness: 0–⅗″ (0–15 mm)depends on materials
15. Workbench Adjustment: Electric
16. Workbed Adjustable Height: 5.9 in. Engraving Speed: 23.6 in. Cutting Speed: 15.75 in. (40 cm/s)
17. Graphic Operating Modes: Optimized Raster, Vector, and Combined
18. Transfer Interface: Flash Drive, USB Cord, Ethernet Cord
19. Net Weight: 374.8 lb.

    (170 kg)

20. Machine Size: 49.6×34.3×36.2 in. (126×87×92 cm)
21. Rated Power: 70W
22. Laser Tube Model: Yongli H1
23. Laser Wavelength: 10.60 μm
24. Laser Tube Diameter: 2.36 in. (60 mm)
25. Laser Tube Length: 43.3 in.
    (1100 mm)
26. Laser Tube Warranty Time: 1 Year
27. Focal lens Dia: 18 mm
28. Focal lens FL: 2.5 in.
29. Mo mirror Dia: 25mm
30. UPC: 797434215499