Simply upload your designs using the included software or via the Ethernet or USB ports, choose your substrate, and the laser will engrave and cut your design with pinpoint precision. In addition to its quality, durability, and the usual long service life, your new laser cutter is also highly practical, with a built-in air assist blowing dust and debris away from the laser head and a digital power supply providing stable high-voltage current and real-time information on your engraver's status. Safe as can be, this laser engraver and cutter can lock its control panel via password and the included keys and automatically cuts off the laser beam if the protective cover is opened. When your work is done, just unlock the casters and wheel it anywhere you want for easy storage and quick transport.Check out our many Accessories and Parts to go along with your laser machine! 60W CO2 laser tube with an estimated lifetime of up to 2,000 operation hours depending on power setting usage and water cooling performance. PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows.
Low Power 10-40% = 1,700-2,000 Hours. Moderate Power 40-70% = 1,300-1,500 Hours.
High Power 70-100% = 800-1,000 Hours. Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber. Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany.
CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered. The RUIDA Motherboard and intuitive RD Control System is easy to use and offers advanced capabilities. Compatible with third party software like LightBurn and AutoCAD.
Two-way pass allows you to feed material into the workbed from the front or back and cut materials larger than your bed size by sliding them through the cabinet. (400×600 mm) workbed gives you plenty of space to work on wood, rubber, plastic, paper, fabric, leather, ceramics, tile, fiberglass, marble, stone, and more-even before you open the integrated pass-through doors that permit you to work on even larger pieces! Our 1000 mm CO2 laser tube provides 60W of power for up to 2000 hours or lasts twice as long when consistently used at lower settings. A crystal-clear LCD display provides real-time information about the device's electric current and autocorrects faults, reducing damage to your laser tube and power supply in the rare case of improper ammeter connections.
The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work. The E-Stop safety button immediately stops the machine in case of emergency.
Engraving Depth: 0.25 in. Workbed Height Range: 9 in. Front/Back Pass Size28.35×1.97 in. Engraving Speed: 23.6 ips (600 mm/s).
Cutting Speed: 15.7 ips (400 mm/s). Included Software: RDWorks 8, CorelLaser. Graphic Operating Modes: Optimized Raster, Vector, and Combined.Transfer Interface: Flash Drive, USB Cord, Ethernet Cord. Net Weight: 209.4 lb.
Machine Dimensions: 44.5×29.5×27.2 in. Laser Wavelength: 10.6 µm. Laser Tube Diameter: 2 in. Laser Tube Length: 39.4 in. 1 x Laser Engraver Machine.
1 x USB Type-A to Type-A Cable. 1 x Ethernet to Ethernet Cable. 1 x Stainless Steel Clamp. 1 x Venting Exhaust Duct 4 ft.
1 x USB Drive with Software. If the weight of your order exceeds 150 lbs. Special circumstances will be stated clearly in the listing.
Please check everything carefully after you receive the parcel, as any damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. Parts must be resaleable and in the original packaging. We cannot take back used products. We cannot take back installed or tired products.
We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria. Return request need to be within 30 days of receipt.OMTech is a collaboration of 30-yr industry vets and promising new techs in Anaheim, California. Our affordable but quality lasers and US-based support quickly grew us into the largest online brand for precision engraving. Alongside our skilled & helpful staff, OMTech users have built up a supportive online family in our forums and social media, sharing inspiration and sharpening their DIY skills together. We love keeping the OMTech family on the cutting edge of laser crafting because we know our growth is inseparable from your success.
All emails will be responded to within 12-24 hours. One 45-minute Virtual Tech Support appointment with OMTech Specialists in Anaheim, California.